[Nasenbaer69]

deleted

 

[Planter21]

Starting level loads, when working up a handload for my 26, have all kinds of FTE's and FTF's. Once the powder charge is up towards normal things work so much better. My 26 doesn't like light ammo.

 

[Nasenbaer69]

deleted

 

[DirtyShirt]

I have a G26 with a booster can on

The gun runs very well without the can, but with the can and subsonic ammo I have a lot of hiccups like stovepipes or failure to eject or feed, maybe 1 or 2 rounds out of 10 do not reloading properly.
Does anyone have experience with G26 and silencers
The gun only ejects the shells very tiredly they land right in front of my feet or from time to time I see them standing upright on the slide
I have now ordered a 14 pound reduced recoil spring in the hope that it will work better.
The barrel is an ceap aftermarket G19 barrel.
I have no idea what is the reason of this issue may bee the Supressor is to heavy or too long or the spring inside the booster is too stiff ???
I read that someone with the same problem had milled a little bit off the locking edge of the barrel and the gun opened earlier and worked fine.
The silencer is a copy of a Brügger and Thomet design and is extremely quiet, so you don't need hearing protection even in closed rooms
The ammunition is loaded really hard 158 Grs FMJ +P load at about 270m/s from the short barrel This ammo works very well in all other guns I try bevore
I would be grateful for ideas and suggestions

View attachment 1130814 View attachment 1130815
View attachment 1130813

270 m/s. Whats that in American?

 

[Rock_Crawler_Jeep]

270 m/s. Whats that in American?

Roughly 890 fps. That's doing the math in my head.

 

[Judge Holden]

I have a G26 with a booster can on

The gun runs very well without the can, but with the can and subsonic ammo I have a lot of hiccups like stovepipes or failure to eject or feed, maybe 1 or 2 rounds out of 10 do not reloading properly.
Does anyone have experience with G26 and silencers
The gun only ejects the shells very tiredly they land right in front of my feet or from time to time I see them standing upright on the slide
I have now ordered a 14 pound reduced recoil spring in the hope that it will work better.
The barrel is an ceap aftermarket G19 barrel.
I have no idea what is the reason of this issue may bee the Supressor is to heavy or too long or the spring inside the booster is too stiff ???
I read that someone with the same problem had milled a little bit off the locking edge of the barrel and the gun opened earlier and worked fine.
The silencer is a copy of a Brügger and Thomet design and is extremely quiet, so you don't need hearing protection even in closed rooms
The ammunition is loaded really hard 158 Grs FMJ +P load at about 270m/s from the short barrel This ammo works very well in all other guns I try bevore
I would be grateful for ideas and suggestions

View attachment 1130814 View attachment 1130815
View attachment 1130813

890 fps with a 158 grain bullet is pretty light especially when combined with a can. Use the OEM spring and simply use standard loads in 115, 124 and 147 grain if you want the G26 to fully cycle.

 

[Nasenbaer69]

deleted

 

[Nasenbaer69]

deleted

 

[Nasenbaer69]

deleted

 

[Emma Johnston]

Roughly 890 fps. That's doing the math in my head.

A velocity of 890 feet per second with a 158-grain bullet is relatively light, especially when using a suppressor. Stick with the original equipment manufacturer (OEM) spring and opt for standard loads in 115, 124, and 147 grains if you want the G26 to cycle fully.