[vinnyv87]

Looks like it won’t sit flush on the slide has anyone had this issue? Brownells slide g17g3 with rmr cut and holosun hs507cx2

 

[GLOCKman_58]

Yes it will not direct mount. You need to use an MOS optic plate. Don’t recommend the thin ones Glock included in packaging. I recommend the C&H precision mos plate. If you want a direct mount into slide you’ll need the holosun SCS or holosun EPS carry optic. Get a quality plate and the optic you have will mount as designed. 🍻

 

[GLOCKman_58]

Here’s the link

V4 MIL/LEO Adapter Trijicon RMR / RMR HD / SRO / Holosun 407C / 507C / 507Comp / 508T / C&H EDC-XL / COMP / COMP MAX / Olight Osight X Fits GLOCK MOS - C&H Precision

Buy V4 MOS Glock to Trijicon RMR Adapter Plate / V4 MOS Glock to SRO / V4 MOS Glock to Holosun 407, 507, 508 | Glock MOS RMR Plate for sale

chpws.com

 

[pgg00]

You said you have an rmr cut aftermarket slide. I'm going to guess there is just enough difference in the measurements they cut to and the Holosun. A few thousandths of an inch will make a difference

 

[GLOCKman_58]

You said you have an rmr cut aftermarket slide. I'm going to guess there is just enough difference in the measurements they cut to and the Holosun. A few thousandths of an inch will make a difference

I guess I didn’t notice it was already rmr cut. My bad

 

[vinnyv87]

Yes it will not direct mount. You need to use an MOS optic plate. Don’t recommend the thin ones Glock included in packaging. I recommend the C&H precision mos plate. If you want a direct mount into slide you’ll need the holosun SCS or holosun EPS carry optic. Get a quality plate and the optic you have will mount as designed. 🍻

It’s not a mos slide it’s a rmr cut slide from Brownells

 

[vinnyv87]

You said you have an rmr cut aftermarket slide. I'm going to guess there is just enough difference in the measurements they cut to and the Holosun. A few thousandths of an inch will make a difference

Yeah I’m going to see if I can find a shop that can file it for me because I’m sure if I send it back to Brownells I might end up getting the same thing

 

[pgg00]

I'd take a fine file and just lightly brush those ends of the slide cut until it fits snug in there.

 

[The_Real_Maxmanta]

Yes it will not direct mount. You need to use an MOS optic plate. Don’t recommend the thin ones Glock included in packaging. I recommend the C&H precision mos plate. If you want a direct mount into slide you’ll need the holosun SCS or holosun EPS carry optic. Get a quality plate and the optic you have will mount as designed. 🍻

I used the Forward Controls MOS adapter. It was for an RMR but they may make one for a Holosun.

 

[vinnyv87]

I'd take a fine file and just lightly brush those ends of the slide cut until it fits snug in there.

I'd take a fine file and just lightly brush those ends of the slide cut until it fits snug in there.

Do you have a picture of a fine file looks like so I can see if I can find one to buy

I used the Forward Controls MOS adapter. It was for an RMR but they may make one for a Holosun.

i don’t have a mos slide

 

[337657]

I'd send it back. You file it, it will take the finish off. Also removes any hope of warranty repair or replacement if there's something else wrong with the slide. I'm sure Brownells has someone else make those slides for them. It's out of tolerance. Or.... is it possible you ordered a slide milled for the Holosun and they sent something else?

 

[bigoldbuck]

Talk to C&H Precision before you send the slide back

 

[Taz]

Interesting. My Brownells G19 slide fit my Holosun. It was a real tight fit though. Required me to drop it on there almost dead nuts straight and push a bit. Almost a slip fit. Can you measure parts?


Sent from my iPhone using Tapatalk

 

[vinnyv87]

Interesting. My Brownells G19 slide fit my Holosun. It was a real tight fit though. Required me to drop it on there almost dead nuts straight and push a bit. Almost a slip fit. Can you measure parts?


Sent from my iPhone using Tapatalk

I’m sending it back they said it shouldn’t have any lip at the bottom of the posts

 

[Bomber Nav]

Definitely send it back. A Holosun 507C x2 (underscore"C") should mount directly on an RMR cut. A 507K is a different story entirely.