close

Privacy guaranteed - Your email is not shared with anyone.

What 's the optimum OAL of reloads for a Wilson Match Barrel in my G21?

Discussion in 'Band of Glockers' started by Poodle, Aug 31, 2006.

  1. Poodle

    Poodle

    Joined:
    Jul 4, 2006
    Messages:
    698
    Likes Received:
    0
    What's the optimum OAL of reloaded rounds for a Wilson Match Barrel in my G21? I'm experiencing stoppages. Might be due to the OAL. The feed ramp of the Wilson Barrel is more steep as compared to the original barrel.
     
  2. Eye Cutter

    Eye Cutter

    Joined:
    Nov 21, 2002
    Messages:
    8,193
    Likes Received:
    2
    Location:
    Dr. B. Eye
    Father P, optimum oal for .45cal is 1.240 - 1.260 in. baka kulang sa crimp yung reloads mo. pag sampa sa ramp, umaatras yung bullet inside the shell kaya tumitigil. pahigpitan mo pa ng konti.

    i-polish mo yung ramp and chamber. baka meron ring mga rough spots yung barrel chamber mo. you will use a dremel and flitz polish. sa True Value hardware meron flitz.

    or you can have mcolikot take a look...expert siya gumamit ng dremel at needle file...
     

  3. vega

    vega

    Joined:
    Sep 29, 2001
    Messages:
    2,799
    Likes Received:
    0
    Location:
    SoCal
    Don't buy a dremel. Tanong mo kay erpat, may binigay ako sa kanya. May kasama ng attachments yon, ang gagamitin mo lang yung parang bulak. Bili ka na lang ng polishing compound.
     
  4. mc_oliver

    mc_oliver

    Joined:
    Feb 21, 2002
    Messages:
    3,499
    Likes Received:
    0
    Location:
    Philippines
    Sa glock, lighter at soldering iron lang ginagamit ko. :supergrin:
     
  5. Eye Cutter

    Eye Cutter

    Joined:
    Nov 21, 2002
    Messages:
    8,193
    Likes Received:
    2
    Location:
    Dr. B. Eye
    yup. use the cone/torpedo shaped polishing attachment. look for the flitz paste sa true value. usually andoon sa may cashier. pati yung trigger bar polish mo na rin.

    Father P, magkapatid ba kayo ni vega?

    tomorrow sabay ka ulit sa amin sa armscor idpa
     
  6. Poodle

    Poodle

    Joined:
    Jul 4, 2006
    Messages:
    698
    Likes Received:
    0
    Magkapatid kami ni vega.

    Na-polish ko kanina. Nilagyan ko ng polishing compound na pang kotse. Tapos nilinis ko ng tubig at kerosene at blow dry para maalis residue. Check ko kung mag-ok na. hanap din ako ng FLITZ. Anong attachment ang torpedo shaped? Yung parang pang-hasa ng kutsilyo ang material? Yung kulay puti lang na parang asbestos ang ginamit ko.

    Mababa ang AOL ng reloads ko. Mga 1.235" lang AOL ng iba (31.36 mm). Ang factory loads consistent sa 32.4 mm (1.275"). Specify ko na AOL everytime magpa-reload ako.
     
  7. vega

    vega

    Joined:
    Sep 29, 2001
    Messages:
    2,799
    Likes Received:
    0
    Location:
    SoCal
    110 volts yung charger, kelangan mo ng stepdown.

    Hindi....

    Saan ka ba pa reload? Ang AOL ko sa 1911 1.275", nung nag-umpisa ako sa 45 sinubukan ko muna 1.260 pero laging may jam sa ramp kahit ginamitan ko ng Lee crimp die. Sa 1.275 wala ng problema.

    Baka naman mahina ang load kaya ayaw mag full cycle?
     
  8. Eye Cutter

    Eye Cutter

    Joined:
    Nov 21, 2002
    Messages:
    8,193
    Likes Received:
    2
    Location:
    Dr. B. Eye
    yung felt/cotton polishing wheel lang. bullet/torpedo shaped or yung cylindrical. huwag yung carborundum na color gray, red or green. kakainin ang metal.

    most likely kulang sa crimp mga reloads. nag-se-setback yan pag tama ng bullet nose sa ramp. specify sa load data na ang oal is 1.240 in.

    kung walang flitz, pwede rin automotive polishing compound pero yung pinaka fine lang. car wax pwede mo rin gamitin but make sure walang maiiwan na residue.