close

Privacy guaranteed - Your email is not shared with anyone.

Pearce Grip - Glock Magazine Extensions and Base Pads

Discussion in 'General Glocking' started by rcarper, May 3, 2007.

  1. rcarper

    rcarper

    Joined:
    Feb 21, 2007
    Messages:
    11
    Likes Received:
    0
    What do you all think of these. I tried a search and didn't get any results. I need them for my 26 and 27 that I picked up today. Thanks in advance.
     
  2. Crazy Ed

    Crazy Ed Senior Member

    Joined:
    Feb 8, 2006
    Messages:
    252
    Likes Received:
    0
    Location:
    Idaho
    I have Pearce +2 for my 19 mags and also the Scherer +2 for both the 19, 17, 20, and 29 mags. All work great and didn't require extra power springs.

    Ed :thumbsup:
     

  3. Butch

    Butch RetiredDinosaur CLM Millennium Member

    Joined:
    Dec 17, 1998
    Messages:
    11,281
    Likes Received:
    370
    Location:
    Minnesota
    Pearce makes great products!



    :patriot:
     
  4. wsweeks2

    wsweeks2

    Joined:
    Apr 28, 2007
    Messages:
    9
    Likes Received:
    0
    Location:
    Suwanee, GA
    I recently purchased a Glock 23 and am looking for the Pearce Grip part that fills in the gap at the bottom of the grip as well as has the extender piece. There is a picture of this on the Pearce website on a G19, but I can't figure out which part this is.

    Any help is appreciated. Thanks!
     
  5. Butch

    Butch RetiredDinosaur CLM Millennium Member

    Joined:
    Dec 17, 1998
    Messages:
    11,281
    Likes Received:
    370
    Location:
    Minnesota
  6. wsweeks2

    wsweeks2

    Joined:
    Apr 28, 2007
    Messages:
    9
    Likes Received:
    0
    Location:
    Suwanee, GA
    [​IMG]

    I'm looking for the one pictured on the G19 in this picture. Any ideas?
     
  7. Crazy Ed

    Crazy Ed Senior Member

    Joined:
    Feb 8, 2006
    Messages:
    252
    Likes Received:
    0
    Location:
    Idaho
    I just received one of the Pearce grip extensions for my G19. It had a little half moon piece that I could have stuck onto the base plate via two small connected rods, if I needed to use it. I don't know if they all come like that, but mine did.

    Ed
     
  8. wsweeks2

    wsweeks2

    Joined:
    Apr 28, 2007
    Messages:
    9
    Likes Received:
    0
    Location:
    Suwanee, GA
    Thanks Ed. What is the part number of the extension you are referring to. I can try to find that and see if it is what I'm looking for.

    Thanks,
    Bill
     
  9. Crazy Ed

    Crazy Ed Senior Member

    Joined:
    Feb 8, 2006
    Messages:
    252
    Likes Received:
    0
    Location:
    Idaho
  10. Butch

    Butch RetiredDinosaur CLM Millennium Member

    Joined:
    Dec 17, 1998
    Messages:
    11,281
    Likes Received:
    370
    Location:
    Minnesota
  11. onduty

    onduty

    Joined:
    Dec 24, 2005
    Messages:
    16
    Likes Received:
    0
    Location:
    East Valley Area, AZ
    The finger extension works great on the G26. I am not sure about the plus 1 and 2 if they will affect the spring pressure?
     
  12. Butch

    Butch RetiredDinosaur CLM Millennium Member

    Joined:
    Dec 17, 1998
    Messages:
    11,281
    Likes Received:
    370
    Location:
    Minnesota
    The spring used in the G26 mags is the same one used in G19 mags, it has plenty of power to work with a +2 cap, I've never had a problem with them.



    :patriot: