close

Privacy guaranteed - Your email is not shared with anyone.

LnL Casefeeder Fix (And it WORKED)

Discussion in 'Reloading' started by EL_NinO619, Jan 12, 2013.

  1. EL_NinO619

    EL_NinO619 EX-Swage Monkey

    Joined:
    Aug 11, 2010
    Messages:
    1,615
    Likes Received:
    0
    Location:
    San Diego
    So I finally got the LnL Casefeeder running non stop. The bowl was never lined up with the V block. It was to far off to the right which would cause the cases to hit the right of the V block, either causing them to lodge horizontally or completely flip upside down. I also opened up holes on the V block shield which brought it closer to bowl and raised it up closer to opening. I will draw up a diagram on where to drill/dremal to align bowl and V block.

    Hope this helps.

    [ame="https://www.youtube.com/watch?v=nwIJAcPKdLg"]LnL Casefeeder Fix - YouTube[/ame]
     
    Last edited: Jan 12, 2013
  2. IndyGunFreak

    IndyGunFreak

    Joined:
    Jan 26, 2001
    Messages:
    26,525
    Likes Received:
    1,776
    Location:
    Indiana
    You got it right at 1:48 :)

    Hope the fix continues to work for you.
     

  3. shotgunred

    shotgunred local trouble maker

    Joined:
    Mar 1, 2008
    Messages:
    9,123
    Likes Received:
    1,397
    Location:
    Washington (the state)
    :rofl:Or buy a Dillon I guess:rofl:

    Glad to hear you got it working.
     
  4. Colorado4Wheel

    Colorado4Wheel

    Joined:
    Nov 2, 2006
    Messages:
    14,990
    Likes Received:
    209
    Location:
    CO
    I did the same thing years ago. I just elongated the existing holes with a file. Solved the problem with flipped cases and cases missing the chute. I never found a way to get the LnL slider and drop mechanism to be even half as good as the Dillon. My last session on my 650 I loaded 500 trouble free rounds. The LnL would struggle to do 50.
     
  5. EL_NinO619

    EL_NinO619 EX-Swage Monkey

    Joined:
    Aug 11, 2010
    Messages:
    1,615
    Likes Received:
    0
    Location:
    San Diego
    I have never had any problem with the slider. I did however have to remove a lot of plastic material.
     
  6. Colorado4Wheel

    Colorado4Wheel

    Joined:
    Nov 2, 2006
    Messages:
    14,990
    Likes Received:
    209
    Location:
    CO
    So you never have cases bounce off the slider arm? Never had case tip as the go in the shell plate? That type of stuff.
     
  7. EL_NinO619

    EL_NinO619 EX-Swage Monkey

    Joined:
    Aug 11, 2010
    Messages:
    1,615
    Likes Received:
    0
    Location:
    San Diego
    No and I am being honest. For awhile I had trouble with double feeds, but that was my fault for not reading the directions and leaving that extension piece on before the drop tube.
     
  8. jmorris

    jmorris

    Joined:
    Apr 13, 2006
    Messages:
    1,943
    Likes Received:
    431
    "Ooh, makes me wonder."

    Way to bring out Led Zeppelin when fixing an LNL.

    Reminds me of a Brian Enos book, I once read.

    Listen close though they knew the answer before the LNL existed.

     
    Last edited: Jan 12, 2013
  9. Colorado4Wheel

    Colorado4Wheel

    Joined:
    Nov 2, 2006
    Messages:
    14,990
    Likes Received:
    209
    Location:
    CO
    Looking at what you load it's only 9mm I would expect to have issues. What gun do you shoot 9mm in?
     
  10. EL_NinO619

    EL_NinO619 EX-Swage Monkey

    Joined:
    Aug 11, 2010
    Messages:
    1,615
    Likes Received:
    0
    Location:
    San Diego
    That is actually .45. 9mm are not Glocks :supergrin: