Glock Talk banner

High Gaps For The Glock 38 Gap ?

736 23
do they sell high caps for the glock 38 ? if so were can i get some or just the reg 8 rounders not just from cdnn ??
1 - 9 of 9 Posts

· Registered
Joined
·
5,741 Posts
Note that a 10-round G37 fits and functions in a G38 (or in a G39). A 7151 extension can be added to any GAP Glock magazine, increasing capacity by one round, so your G38 can have an eight, nine, ten or eleven round magazine. What it CAN'T have is more rounds in the flush-fitting G38 mag--there just ain't any more room!
 

· Registered
Joined
·
5,741 Posts
Originally posted by Amrcn-Bulldogg
Gary, were can i get A 7151 extension ?
Any of the Usual Suspects (GlockParts, Glockmeister, Lone Wolf, etc.) on the web.
 

· Registered
Joined
·
5,741 Posts
Originally posted by Amrcn-Bulldogg
ALSO WHY IS THAT A G-37 CAN FIT IN THE G-38 WHY DIDNT THEY DESIGN IT THAT WAY IN THE G-38 AHAA ??
Within a Glock caliber family, the longer magazines always fit in the shorter-gripped models. The G37 mag is longer than the G38 mag, so it holds more rounds and sticks out of the G38's grip by an inch or so.
 

· Registered
Joined
·
5,741 Posts
The Glock 9mm magazine is EXACTLY THE SAME SIZE as the Glock GAP magazine! A 7151 will fit just fine. Glockmeister (and others) may not have bothered updating their websites to reflect this.
 

· Registered
Joined
·
5,741 Posts
Originally posted by Vista
Gary: Do you know if the A&G Grip Extension "slim" model would properly adapt a G37 magazine to a G38 grip? It should work since the "slim" adapts a G17 mag to a G19, and a G22 mag to a G23.

Vista
Unlike the 7151, I have no experience with the A & G on a GAP mag--BUT it should work for the reason you cite; the G37 mag is the same size as the G17 mag.
 

· Registered
Joined
·
5,741 Posts
Originally posted by Glocks&Ducs
I think Glock could have designed the G39 magazine to hold one or two more rounds. If you have a G39 mag, pop the floorplate off and look at the inside. It has the same "limiting" ridges as the 10 round clinton ban mags used to have during the ban. Actually they still do, if you are still limited to 10 rounders.
I hadn't noticed--but the question is: are the ridges there to LIMIT capacity or for feeding reliability? (I don't know why Glock would seek to limit a G39 mag to six rounds.)
 

· Registered
Joined
·
5,741 Posts
I've seen some posts from other folks who say they can get 9 rounds in their G38 mags. I certainly noticed that it is much easier to get the eighth round in a G38 mag than the tenth round in a G37 mag!
 

· Registered
Joined
·
5,741 Posts
Originally posted by Glocks&Ducs
I agree that 10th round can be a bear. That is where the trusty Glock supplied loader, the one most proclaim as garbage, becomes perfectly handy.
The Glock loader...I don't leave home without it (or without my HKS loader).
 

· Registered
Joined
·
5,741 Posts
Originally posted by DannyR
The spring pressure in the G39 mags might be so great as to need the reinforcing ribs. It requires very strong springs to complement the rapidly moving slide.
Danny, I have Pearce PG-39 and PG-2733 extensions on my G39 mags--but they all have stock springs. The PG-39, like the Glock 7151, increases capacity by one round; the PG 2733 doesn't increase capacity with GAP rounds but (a) gives my little finger something to hang onto and (b) makes loading the sixth round easier and inserting a fully loaded mag when the slide is forward easier as well. Would you anticipate any reliability problems with the stock G39 mag springs with these extensions?
 
1 - 9 of 9 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top