close

Privacy guaranteed - Your email is not shared with anyone.

Any Problems With This ???

Discussion in 'General Glocking' started by SAWMAN, Mar 18, 2012.

  1. SAWMAN

    SAWMAN

    Joined:
    Aug 19, 2006
    Messages:
    522
    Likes Received:
    3
    Location:
    NW FLA.
    I have a OD Glock 19(Gen 3). I want to turn it into a Glock 32. Specifically,into a OD Glock 32. Can I swap everything from my 19 into/onto my OD Glock 19 frame ?? Will the weapon be mechanically the same ?? Any problems with fit and function ?? How about the legalities of the serial nimbers ??(slide,bbl,vs frame)

    Any info would be appreciated from you Glock "GURU's" out there. Thank you for your input. --- SAWMAN
     
  2. SCC

    SCC Member Me

    Joined:
    Jun 10, 2007
    Messages:
    8,107
    Likes Received:
    20
    Location:
    kennesaw GA.
    is it a 3 pined glock19 ?
     

  3. voyager4520

    voyager4520 -----

    Joined:
    Apr 25, 2009
    Messages:
    8,589
    Likes Received:
    1
    Location:
    SE Colorado
    You need to change the trigger housing w/ejector to one for .40/.357.

    As far as I know, all OD frames are 3-pin and have the extra reinforcement on the front frame rail insert necessary for shooting .357SIG.
     
  4. SCC

    SCC Member Me

    Joined:
    Jun 10, 2007
    Messages:
    8,107
    Likes Received:
    20
    Location:
    kennesaw GA.
    WANTED TO ASK FIRST !!! JUST TO MAKE SURE IT IS A 3 PINED GLOCK :supergrin:
     
  5. SAWMAN

    SAWMAN

    Joined:
    Aug 19, 2006
    Messages:
    522
    Likes Received:
    3
    Location:
    NW FLA.
    Yes gentlemen it is a 3 pin(G3)model. Did not think about the trigger group with it's 9mm sized ejector. Would I have to buy a whole new trigger group ?? I don't believe that you can change JUST the ejector can you ?? Are all the ejectors the same as far as angle of bend,thickness,etc ?? --- SAWMAN
     
  6. voyager4520

    voyager4520 -----

    Joined:
    Apr 25, 2009
    Messages:
    8,589
    Likes Received:
    1
    Location:
    SE Colorado
    You can change just the ejector but the ejectors are not sold individually, you have to buy the trigger housing which already contains the ejector you want. The one you'd want is the Gen3 .40/.357 trigger housing w/ejector, Glock manufacturer part number 1896, and all you'd do is pull the 9mm trigger housing out of the frame and drop the .40/.357 trigger housing w/ejector into the frame. No other parts need to be changed in the frame.

    Here are some detail strip resources if you need them, you'll need a 3/32 inch punch such as the Glock Armorer's Tool:
    [ame="http://www.youtube.com/watch?v=oV0wDDFV0NY"]Glock Detail Strip And Reassembly (IN HD) - YouTube[/ame]

    On the following page are some Glock Armorer's Manuals, just scroll down to the "G" section. I learned from the Update Manual and 2009 Manual. The 2009 Manual has a few pages missing, but that info can be found in the Update Manual as well.
    http://stevespages.com/page7b.htm

    Correct slide stop spring position: http://glocktalk.com/forums/showpost.php?p=15738529&postcount=3

    Here's an easy way to disassemble and reassemble the firing pin assembly:
    http://www.tgscom.com/images/sharedimages/Glockworld/SD12.jpg
     
    Last edited: Mar 18, 2012
  7. SAWMAN

    SAWMAN

    Joined:
    Aug 19, 2006
    Messages:
    522
    Likes Received:
    3
    Location:
    NW FLA.
    voyager, thanks for that sir. I found the trigger housing(w/ ejector) at the Lone Wolf site(GLO-1896) for $6.75. Will pull my trigger parts out and reinstall in that housing. Will use the G32 complete upper so the extractor will be good to go. Thanks again --- SAWMAN