Glock Forum - GlockTalk banner
polymer80
1-15 of 15 Results
  1. General Firearms Forum
    So basically yesterday I just completed my p80 build for the Glock 26. And immediately I noticed issues with the rounds ejecting, the slide would only go 90% of the way back. I can see the round still being held in place by the extractor and it took a lot of racking back and forth to get it out...
  2. General Glocking
    I am looking fro Gen 3 Glock g17 pin measurements as well as the pin measurements, size and or dimensions for its counter part polymer80 G17 in millimeters Trigger Pin diameter and length in mm Trigger Housing Pin diameter and length in mm Locking Block Pin diameter and length in mm Polymer80...
  3. General Firearms Forum
    I had a front locking block issue with my p80 when I built it. I could not get the slide on at all because of the issue. I got the new front locking block in the mail yesterday and it fit in with no problems. Right as I mated the frame with the slide and tried to pull the slide back, it started...
  4. General Firearms Forum
    Hello, I built a Polymer80 Glock 26 with all Glock OEM parts including Glock magazines. I have medium/large hands so my pinky finger, sometimes two fingers will go below the magazine and apparently are pushing up. This causes every type of failure because the magazine gets in the way of the...
  5. General Glocking
    [Deleted]
  6. General Firearms Forum
    Hey guys new to the forum here. Bare with me as this is my first P80 build and I understand it isn’t a Glock. Anyways, I just recently tly purchased a PF940C Frame W/ Jig and I have just received it in the mail. After opening the package and looking at the frame, I noticed something odd that I...
  7. Introduction Forum
    Hey guys, I’m new to the forum and pretty new to glocks. I’m glad I finally joined though, from what I’ve read so far this seems like a great community of people. I’ve always been a fan of doing things with my hands(working on cars, building PC’s, etc) so when I discovered p80’s I had to build...
  8. General Firearms Forum
    Hey. I’m not new to glocks but I am new to P80’s (yes I know a p80 isn’t a Glock but uses Glock parts) I have a P80 build I feel like I am very close to finishing. Every time I fire a round, the magazine falls out and the spent round is stuck. This has been very much a budget build (wife is...
  9. Gun-Parts & Access.
    Is Polymer80 still making these 80% frames? I can't seem to get an answer through searching.
  10. Gunsmithing
    I heard that a G26 gen 5 upper is not backward compatible to gen 3 frame. However, my gen 5 upper fits my Polymer80 subcompact as well as did my gen 3 upper. To the best of my recollection, I've not fired it in this 5 over 3 configuration. But I want to try it. Has anyone done this.
  11. General Firearms Forum
    I ordered a pf940c from glockstore and the M4 hole on the jigg was out of spec, got an rma from Polymer80 today and after checking yet again, the m4 hole is out of spec. The problem is that the M4 holes will not line up with the locking block and when trying to insert the pin, it taps against...
  12. General Firearms Forum
    The 80% came today. Slight misalignment of the lockingblock-triggerpin hole. Nevertheless, mildly brutish force saved the day. I had to shave down the front rails. Anyway, here is it, with an Advantage Arms .22LR upper. Fired just 10 shots and no problems.
  13. General Firearms Forum
    Hey new guy here, I completed my glock 34 and I just wanted to share the results. It's a polymer80 v2 build with an Alpha Wolf Slide and barrel and all other parts are stock glock. I fired about 200 rounds through it today and she ran flawlessly, which is more than I can say for the v1 I...
  14. General Firearms Forum
    A snapshot of my current project. Pretty happy with the results so far. Lower is a Polymer80 PF940v2 Readymod, stippled by me. Upper is a G34 slide machined and Cerakoted by Southwest Precision Arms. RMR-ready milling as well. Still debating on what to do for sighting. My options are regular...
  15. Gunsmithing
    I wanted to start a separate thread for my first Polymer 80 build. I say first because before I'd even started, I'd ordered multiple colors of frames. Thinking that I'd want to make one of them all. I was a little skeptical going in, but like a lot of folks, I'd seen a gazillion YouTube videos...
1-15 of 15 Results
Top