Glock Talk banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 27 Results
  1. Valuable Info
    Hello, brand new to the community and was wondering if anyone could point me in the right direction for a p80 drill guid/jog that I can3D print I figure it has to be out there somewhere but it seems impossible to Find. Any help will be appreciated thank you
  2. General Firearms Forum
    While assembling my G19 Poly80 with a Rock slide upper I took it shooting but I noticed it was simi-difficult to rack. I disregarded it however as I’m new to Glock‘s and I assumed it was natural. However after going to my local store and looking at their gen 5, 19 and gen 3, 29(10mm) I noticed...
  3. Gun Parts & Accessories
    got this Poly80 Glock 43 gray frame, PF9SS, for a build that I have decided not to do. Everything included that comes from the factory. $120 including USA shipping and PayPal. Thanks
  4. General Firearms Forum
    I just finished (for the most part) this pf940v2 build today and it’s working really well except for one minor issue. I’ve got a stock Glock LPK (came out of a 22 but I put a 9mm ejector in the trigger housing) in the frame and when the slide is off and I go to put it back on, the trigger bar...
  5. General Firearms Forum
    I own multiple different Glocks, including Glock 19 and Glock 17. I like to go to the local shooting range with few of my local friends. I've been seeing more and more people talk about Polymer 80 builds. I also notice that many people are comparing P80 to Glock. What is the difference between...
  6. General Firearms Forum
    So basically yesterday I just completed my p80 build for the Glock 26. And immediately I noticed issues with the rounds ejecting, the slide would only go 90% of the way back. I can see the round still being held in place by the extractor and it took a lot of racking back and forth to get it out...
  7. General Firearms Forum
    Hey guy’s I’m in the process of sorting out some of the bugs of my first polymer 80 build PF940V2 9mm. So I have about 500 rounds through the gun, no trigger issues and the gun is pretty dead accurate. The issue that I am having is the first 3 mags will give me stovepipes FTE, after that the...
  8. General Firearms Forum
    Hey guys, I got a p80 g17 recently and it slides smooth as butter but when I chamber a round, the striker doesn't recede fast enough causing it to catch on the top of the rim and cause failure to feed. Any ideas on what it could be causing this to happen? Keep in mind it has no problem feeding...
  9. Gunsmithing
    First post here. I'm completing my first p80 build and when I cycle dummy rounds through the gun, every round pulled from the magazine gets hung up on the firing pin! I'm including a photo for reference. The firing pin will reset, but only at the very last moment before chambering a round. I'm...
  10. Articles
    I build a P80 PF940v2 G17 but I messed up my pin holes and I was just wondering if anyone had an extra jig that they can sell or give me for this frame “PF940v2”, I’m able to fix the holes but I’m not able to redrill with the same jig since they’re not centered anymore
  11. General Firearms Forum
    Hi everyone! This is my first post, so apologize if I'm a bit of a noob. Thank you in advance for your time! So I recently assembled a Gen3 G19 using a Polymer 80 lower and a LFA upper. Gun looks great, cycles great, feels great, but there's one small issue I can't seem to figure out. Whenever...
  12. Gunsmithing
    Hi guys, I am doing a P80 build. Everything has worked so far except I cannot get the slide fully into battery. I am hanging up on the locking block and the barrel lug. A factory barrel fits into the build just fine. I didnt have calipers with me to measure the dimensions when I had the...
  13. General Firearms Forum
    I had a front locking block issue with my p80 when I built it. I could not get the slide on at all because of the issue. I got the new front locking block in the mail yesterday and it fit in with no problems. Right as I mated the frame with the slide and tried to pull the slide back, it started...
  14. General Glocking
    Built a polymer 80 pf940v2. I haven't fired it yet, and wanted to get some advice before I do. The metal on my slide where the barrel meets the ejection port is a little warped and formed a lip. It's it safe to shoot? If not, should I get a new slide or can I just sand it down?
  15. Gun-Parts & Access.
    Anyone have experience with lone wolf slides? Anyone have experience with Faxon barrels? Will they play nice together or are the tolerances wrong with the combination? Thanks in advance if anyone has any knowledge or opinion.
  16. Gunsmithing
    Wanted to share my first build and welcome any feedback positive or negative. I had a full month of waiting on backorder to watch all of the instructional videos and download the pdf guides.. Before i start i gathered what tools i have which are 1.)Dremel with additional attachments for sanding...
  17. General Firearms Forum
    Hey everyone, first time poster, hopfully I join the best forums out there lol. I have a glock 34 ZP slide, ZP barrel (Zaffiri Precision) that I put on top of a P80 brand standard size frame compatible with 17/22/34 something like that. I got everything together and only problem is the trigger...
  18. Gunsmithing
    I am not sure why I am having so many issues building this damn thing. I have built many rifles, but his thing has got me frustrated. It's so simple it stupid, or most likely it just me. Bought an SS80 lower with Glock 43 trigger kit. I got the OEM 43 slide in the mail yesterday, slapped the...
  19. General Firearms Forum
    Hi, I recently built a polymer 80 and have had some setbacks to having the build 100 percent functional. Firstly, when I completely assembled the build, the trigger wasn't disconnecting, I would completely pull the trigger and the striker wouldn't release. So I read on another forum, a guy said...
  20. Gunsmithing
    Hi, I just completed my P80 subcompact build. It was not my 1st attempt at an 80%. I’ve done some AR lowers & a P80 full size. The subcomact was extremely challenging. Not because it’s subcompact, but because the holes didn’t line up. I had to drill the holes in the rear rails out 1/32...
1-20 of 27 Results
Top