Glock Forum - GlockTalk banner
p80
1-19 of 27 Results
  1. General Firearms Forum
    I own multiple different Glocks, including Glock 19 and Glock 17. I like to go to the local shooting range with few of my local friends. I've been seeing more and more people talk about Polymer 80 builds. I also notice that many people are comparing P80 to Glock. What is the difference between...
  2. IMG_20210809_222213_01.jpg

    My G26 P80 thin blue line build. Very happy with outcome and cost.
  3. 20210809_174350.jpg

    G26 P80 custom build. Thin blue line.
  4. General Firearms Forum
    So basically yesterday I just completed my p80 build for the Glock 26. And immediately I noticed issues with the rounds ejecting, the slide would only go 90% of the way back. I can see the round still being held in place by the extractor and it took a lot of racking back and forth to get it out...
  5. Gunsmithing
    I've got a Polymer 80 Glock 19 build that won't go into battery. I haven't test fired it yet, but when I put a magazine on a locked open slide and let it go home, it doesn't go all the way into battery. I'm using a PF940CV1 frame with a Rockey Brass Frame Parts Kit and a Rock Slide USA Slide...
  6. General Firearms Forum
    Hey guys, I got a p80 g17 recently and it slides smooth as butter but when I chamber a round, the striker doesn't recede fast enough causing it to catch on the top of the rim and cause failure to feed. Any ideas on what it could be causing this to happen? Keep in mind it has no problem feeding...
  7. Gunsmithing
    A question about lower build kits: Some kits seem to have different parts. (I’m building a full size for 10 mm) The lower build kit from the Glock Store contains a “locking block” but other kits don’t seem to have it. Doesn’t this part come with the P80? Is it an upgrade part, or do I just use...
    p80
  8. General Firearms Forum
    First build and the g19 wont cock/go all the way back i think the Barrel supposed to go over the frame right next to where the magazine is so the bullet can enter but it gets stuck on the rail if i hard cock it the Barrel and recoil spring hangout a bit Glock 19 Nitride Replacement Barrel Will...
  9. Gunsmithing
    Hi guys, I am doing a P80 build. Everything has worked so far except I cannot get the slide fully into battery. I am hanging up on the locking block and the barrel lug. A factory barrel fits into the build just fine. I didnt have calipers with me to measure the dimensions when I had the...
  10. General Firearms Forum
    I had a front locking block issue with my p80 when I built it. I could not get the slide on at all because of the issue. I got the new front locking block in the mail yesterday and it fit in with no problems. Right as I mated the frame with the slide and tried to pull the slide back, it started...
  11. General Glocking
    Just saw a video on the development of this new Glock P80. View: https://youtu.be/woUExYRrpIE Very cool project. I’ve not fired a Gen 1 but I’ve heard from several Glock fans that the Gen 1 was their fav.
  12. General Glocking
    Built a polymer 80 pf940v2. I haven't fired it yet, and wanted to get some advice before I do. The metal on my slide where the barrel meets the ejection port is a little warped and formed a lip. It's it safe to shoot? If not, should I get a new slide or can I just sand it down?
  13. General Glocking
    [Deleted]
  14. General Firearms Forum
    Hey guys new to the forum here. Bare with me as this is my first P80 build and I understand it isn’t a Glock. Anyways, I just recently tly purchased a PF940C Frame W/ Jig and I have just received it in the mail. After opening the package and looking at the frame, I noticed something odd that I...
  15. Gun-Parts & Access.
    Anyone have experience with lone wolf slides? Anyone have experience with Faxon barrels? Will they play nice together or are the tolerances wrong with the combination? Thanks in advance if anyone has any knowledge or opinion.
  16. Introduction Forum
    Hey guys, I’m new to the forum and pretty new to glocks. I’m glad I finally joined though, from what I’ve read so far this seems like a great community of people. I’ve always been a fan of doing things with my hands(working on cars, building PC’s, etc) so when I discovered p80’s I had to build...
  17. General Firearms Forum
    Hey. I’m not new to glocks but I am new to P80’s (yes I know a p80 isn’t a Glock but uses Glock parts) I have a P80 build I feel like I am very close to finishing. Every time I fire a round, the magazine falls out and the spent round is stuck. This has been very much a budget build (wife is...
  18. Gun-Parts & Access.
    Is Polymer80 still making these 80% frames? I can't seem to get an answer through searching.
  19. Gun Parts & Accessories
    Please send PM or email for contact. PayPal friends and family otherwise +3% or Zelle. SOLD $80 Shipped - NIB P80-PF940v1.5-BLK Polymer80 PF940v1.5 Full Size 80% Pistol Frame Kit Glock 17, 17L, 22, 24, 31, 34, 35 SOLD $80 Shipped - Victory First Brownells Edition Glock 17 Non Threaded Barrel -...
1-19 of 27 Results
Top