Glock Talk banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-19 of 91 Results
  1. Gun Parts & Accessories
    I am going through storage and posting items I will not be using. most are new unless noted. Zev Pro Glock 17 Gen 1-4 barrel, bronze $175 shipped Zev Pro V2 Compensator 1/2x28 $85 shipped Zev Pro V2 Comp 1/2x28 (installed on firearm but not shot) $65 Zev Pro connector $12.00 (if purchased with...
    $115 USD
  2. Gun Parts & Accessories
    Used parts G22 g4 oem barrel with rsa-$75 shipped SOLD G19 gen 5 marksman barrel-$75 shipped SOLD Glock 43 oem mag with tti +1 and amend 2 with ghost plus 2-$65 shipped Assorted parts some oem-$65 shipped
    $75 USD
  3. Gun Parts & Accessories
    I am looking to sell/trade my stag 5.56 upper comes with redfield 3x9 scope, strike Industries latchless charging handle, also includes the BCG, 2 20 round metal magazines, 1 Lancer weapon system 10 round magazine, Hogue Rubber Grip, upper has 60 rounds through it, Has marks on in from handling...
    $700 USD
  4. Gun Parts & Accessories
    Ended up not needing this as I went a different route and ended up with a G19 instead. Used but unknown round count. I've not used them at all but I picked them up used. Just normal signs of wear as far as I can tell. A couple people have reached out but no one has committed to purchase yet...
    $65 USD
  5. Gun Parts & Accessories
    I started with a factory Glock 19 upper, added steel three dot sights, then a custom stainless steel Match barrel with target crown (see pics), then had the slide cerakoted Gray. $350.00 includes priority mail, with insured shipping to the lower 48 states within two days of receiving the postal...
    $350 USD
  6. Gun Parts & Accessories
    4.7 inch 9mm barrel. Sig sauer original barrel for full size p320. 140 shipped Paypal ok
    $140 USD
  7. Gun Parts & Accessories
    For sale is a brand new (un-fit, un-modified) KKM Bull barrel in 9mm. Clark / Para ramp cut. 4.25in commander length. $ 175 shipped No trades.
    $175 USD
  8. For Sale CLOSE

    Gun Parts & Accessories
    XXX
    $1 USD
  9. General Glocking
    Hello! had a question about my Glock 17 I’ve had this firearm now for a year and clean it after every time after the range I’ve shot maybe 200 rounds in total through it, but for some reason I just noticed some type of streaks in the barrel that looks like rust, the gun has never been exposed...
  10. Black Rifle Forum
    Hey guys, I'm looking for brand recommendations for a 300blk barrel. I have decided I want an 8.5" but haven't picked a manufacturer yet. I was leaning towards a BA Hanson profile 8.3" pistol length gas pinned gas block but am open to suggestions. If I could find an FN barrel that would be...
  11. General Glocking
    A few days ago I looked at my brand new Glocks that I had stored in a closet for over 4 years and they look brand new except for inside the barrel. Every other line inside the barrel, the non-black lines, are orange brown (rust) color. It looks more like a stain, but rust colored. When rust...
  12. General Glocking
    I buy guns and store many of them for years without using them, factory new, since usually I buy duplicates; sometimes triplets or even quadruplets. I live in a pretty hot and dry region so I thought they were perfectly safe in their factory cases aince I'd never shot or even cleaned them...
  13. 1911 Forums
    Hello guys, I have a Rock Island full size doublestack 10mm 1911 and am looking at converting it to .40SW. I found a barrel that fits my description but have a question: is there a difference between single stack and double stack 1911 barrels? I am new to 1911s and am learning about customizing...
  14. General Glocking
    Hello everyone, I am doing a research project on different rifling methods, specifically aftermarket barrels because they are not proof tested. I was wondering if anyone knew of any aftermarket barrels that are compatible with the Glock 19 gen 2-4 that uses hammer forging or ECM. I have button...
  15. Gun Parts & Accessories
    I've accumulated some parts intended for builds I was doing or in some cases the parts were just included in a trade deal I made. Bottom line is I have some extra parts I don't need. I have two G19 barrels. Flush cut and crowned. I do not know the maker. One is blank/no rollmark and the...
    $80 USD
  16. Gun Parts & Accessories
    Cleaning out the parts drawer. Parker Mountain Machine threaded barrel (G19) and single port comp (Gen5) for sale. Both are used and show signs of wear. Functionally sound. comp works great with reduced recoil spring. Barrel - $45 shipped Comp - $25 shipped
  17. General Firearms Forum
    Does anybody know where I can find a 20" Encore barrel chambered in .475 Linebaugh? I've checked MGM, EABCO and Bullberry. Nobody seems to be making them right now.
  18. Black Rifle Forum
    Hey guys, I have been working on a project AR10 with emphasis on weight. I shaved the rifle down to 8.5lbs without optics/mag but accuracy is less than acceptable to me; It is generally a 2-3 MOA rifle with the exception of Barnes TTSX (sub-MOA out to 200yds). Barrel is Faxon 18" pencil profile...
  19. Wanted To Buy
    I am looking for a factory Glock 32 barrel that will fit a 4th gen. Thanks! Kindly, RW
1-19 of 91 Results
Top