close

Privacy guaranteed - Your email is not shared with anyone.

Welcome to Glock Talk

Why should YOU join our Glock forum?

  • Converse with other Glock Enthusiasts
  • Learn about the latest hunting products
  • Becoming a member is FREE and EASY

If you consider yourself a beginner or an avid shooter, the Glock Talk community is your place to discuss self defense, concealed carry, reloading, target shooting, and all things Glock.

Tightening up a thumb safety?

Discussion in '1911 Forums' started by kirklite99, Dec 13, 2010.

  1. kirklite99

    kirklite99

    239
    0
    Dec 10, 2010
    I have a RIA 1911A1-MS which has been a fantastic pistol...dead nuts reliable and accurate. However, I've always wanted to tighten up the thumb safety. What's the best way to make it "snappier"...as in more positive in CLICKING on/off? The only other 1911 I have is a Kimber and that safety snaps on and off like a light switch. Very positive. The RIA is just plain mushy. What parts would need replacing besides the thumb safety? I'm guessing the safety plunger and a stronger spring would be in order, too. Would a new thumb safety need to be fitted by a gunsmith? Thanks in advance!
     
  2. Brownells sells a bit that fits through the plunger tube and puts a good detent on the thumb safety.
    That would make it snappier for sure.
    Check it out before you go replacing perfectly good parts.
     


  3. Try a new spring in the plunger tube.

    If not, then you can try to reprofile the engagement area; making a sharper corner.

    The last resort is a new thumb safety. And yes, it will need to be fitted. You can do it, if you have the file and stone.
     
  4. pistolwrench

    pistolwrench Dremel jockey

    642
    6
    Jul 27, 2009
    Also check the radiused end of the plunger.
    Many are made of soft steel and the dome gets worn.
     
  5. FLIPPER 348

    FLIPPER 348 Happy Member

    22,868
    3,038
    Oct 7, 2000
    Bend Oregon
    the 2nd option will give you the best results
     
  6. kirklite99

    kirklite99

    239
    0
    Dec 10, 2010
    Thanks for the help, everyone! I think I'll try a new plunger/spring combo. No grinding/fitting and probably the cheaper way to go over a new thumb safety. I guess I could always try my Kimber safety parts in the RIA and see if that "snaps" it up... I have no problem with detail stripping a 1911.
     
  7. Texas Bulldog

    Texas Bulldog

    356
    0
    Oct 28, 2009
    I had the same gripe about my Nighthawk. I was PISSED i spent that much on it and i had to put my time into fixing what should have been done right. Granted they did offer to take it back and fix it but i had a spare wolff spring from brownells. I put a new spring in there and it was night and day.

    it still wasn't as snappy and "positive" feeling as most of my other 1911's but it was "Good"... i didn't want to sharpen the edge of the safety because of the coating on it so i haven't yet but i may soon and just touch it up with some other form of coating. I wish it was stainless, that would have been very easy.

    But yeah, do the spring first. order the 3 pack just to have them IMO.... always good to have spare parts.

    JOe
     
  8. kirklite99

    kirklite99

    239
    0
    Dec 10, 2010
    I'd have been pissed, too, but we're talking about a sub-$400 Filipino 1911. So far, I'm very pleased with the reliability, accuracy and overall fit and finish for such a "cheap" 1911. The mushy safety was perfectly acceptable, to me, but I was wondering how to make it "snappier", especially if it were an easy fix. I'll try the Wolff spring. I've had nothing but great experiences from the many recoil springs I've bought from them.
     
  9. FLIPPER 348

    FLIPPER 348 Happy Member

    22,868
    3,038
    Oct 7, 2000
    Bend Oregon
    Don't waste your $$$, the problem is with the detent in your thumb safety.
     
  10. kirklite99

    kirklite99

    239
    0
    Dec 10, 2010
    Really? Then why didn't it "snap up" when I tried my Kimber thumb safety in the Rock? :dunno:
     
  11. Texas Bulldog

    Texas Bulldog

    356
    0
    Oct 28, 2009
    i bet its the spring....

    besides, if its not.... you have a spare part and spare parts are always good. Not to mention its as cheap of a part as you can get.

    Like troubleshooting anything, always start with the cheapest and easiest and then go from there.

    Besides, its not like it is the only gun you have for protection or shooting and its not working, it just has a mushy thumb safety.

    JOe
     
  12. kirklite99

    kirklite99

    239
    0
    Dec 10, 2010
    Yup...

    Again, yup... Cannot hurt at all to order a cheap spring. I'll try a new plunger, too. Don't even have to take the frame all the way down to change those out.

    And, that's exactly what I intend to do.

    Very true. I have many other options. I don't even carry it. Like I said, I was VERY surprised at how reliable and how well an under $400 Filipino-made 1911 could be. Just wanted to "tighten up" the thumb safety. Even the finish is quite decent and seems to be wearing better than my much more expensive Kimber, which I don't carry, either, so holster wear isn't a competing issue. :upeyes:
     
    Last edited: Dec 15, 2010
  13. Texas Bulldog

    Texas Bulldog

    356
    0
    Oct 28, 2009
    Cool, i hope you didn't take my recommendation in a negative way. I was more replying to the other post saying don't waste your time/money.

    I have a 3 Rock Islands. They are amazing for the money :wow: I am going to send them to my local guy to cerakote 2 of them and hard chrome 1. thats the only downfall on mine is the cheap coating. But for the money its a huge bargain.

    1 budget gun that has really shocked me in terms of actually being better than the Rock Island, especially in the finish department is the Metro Arms American Classic II. I want to order the "Trophy" next but im putting my change in the "Range Officer" jar first. :supergrin:

    So many great guns, not enough money :crying: