close

Privacy guaranteed - Your email is not shared with anyone.

Sight Pushers ready

Discussion in 'Sights, Optics and Lasers' started by BigMoneyGrip, Jul 9, 2010.


  1. BigMoneyGrip

    BigMoneyGrip
    Expand Collapse

    Joined:
    Feb 9, 2009
    684
    24
    Location:
    Oxford, MS
    I have some more pushers ready if anybody wants one. Here is a write up that 911boss made
    http://www.wilsonvilleusa.com/guns/BMGSightTool.htm
    You can paypal $67.25 to scott@phy.olemiss.edu or send a Money Order for $65 to
    Scott Watkins
    4 CR 3027
    Water Valley, MS
    38965
    The new ones have the jaw raised by .187 to help counter the problem some people were having with the slide twisting. Also, all aluminum is hard coat anodized.
    Thanks,
    Scott.
     

    Wanna kill these ads? We can help!
  2. boonsht

    boonsht
    Expand Collapse

    Joined:
    May 25, 2005
    10
    0
    Location:
    Illinois, USA
    Paypal sent!
     

  3. bruscifer

    bruscifer
    Expand Collapse

    Joined:
    Feb 26, 2009
    60
    21
    Location:
    Texas
    Paypal sent
     
  4. simmy952

    simmy952
    Expand Collapse

    Joined:
    Jan 26, 2009
    573
    0
    Same here. Thanks.
     
  5. BigMoneyGrip

    BigMoneyGrip
    Expand Collapse

    Joined:
    Feb 9, 2009
    684
    24
    Location:
    Oxford, MS
    I got them all, they will be going out today.
    Thanks.
     
  6. husker54

    husker54
    Expand Collapse

    Joined:
    Mar 22, 2006
    317
    1
    Location:
    nebr.
    I received mine today and it worked flawlessly on a 19, 22 and 26. looks great and functions very nicely.
     
  7. GulfCoastTider

    GulfCoastTider
    Expand Collapse

    Joined:
    Jan 17, 2009
    25
    1
    Location:
    Alabama
    BMG
    Received my sight Pusher today, thanks for the quick turn around. Looks great, can't wait to put it work!
     
  8. Underwhere

    Underwhere
    Expand Collapse

    Joined:
    Apr 9, 2007
    154
    0
    Location:
    MA
    So this will work on say the Warren sights?
    Or do I need a different tool?
     
  9. bentbiker

    bentbiker
    Expand Collapse
    NRA Member

    Joined:
    Sep 11, 2009
    4,554
    5
    Location:
    Orange County, CA
    I believe the sides of the Warren sights are vertical. That means two things. First, the slope of the pusher will hit on a shoulder and might make a mark; you can probably get around this by putting a business card between the two metal surfaces. Secondly, the Warren sight is very low profile over the dovetail, so you will want a well measured shim to allow the pusher to just clear the slide, and the max width of the sight should be about 15/16" for the pusher to straddle the sight (the Warrens look wide). Bottom line is I'd be very surprised if it won't work, but I haven't done it.
     
    #9 bentbiker, Jul 21, 2010
    Last edited: Jul 21, 2010
  10. BigMoneyGrip

    BigMoneyGrip
    Expand Collapse

    Joined:
    Feb 9, 2009
    684
    24
    Location:
    Oxford, MS
    If the side of the sights are vertical, use the side of the pusher and not the cutout. I made it this way so it would work either way. The inside or cutout, works better with angled sights and the side of the pusher works best with the straight sights.
     
  11. bentbiker

    bentbiker
    Expand Collapse
    NRA Member

    Joined:
    Sep 11, 2009
    4,554
    5
    Location:
    Orange County, CA
    That works for removal, but when installing, unless the sight can be pushed most of the way into the dovetail without the tool, there isn't room for the pusher to the side of the slide where the sight is sticking out. You can start it within the cutout, and then, when it is most of the way in and getting tighter, reposition everything and push the rest of the way with the side.
     
    #11 bentbiker, Jul 22, 2010
    Last edited: Jul 22, 2010