close

Privacy guaranteed - Your email is not shared with anyone.

Crimped primers in 9mm?

Discussion in 'Reloading' started by Kwesi, Nov 3, 2010.


  1. Kwesi

    Kwesi
    Expand Collapse

    Joined:
    Sep 23, 2006
    1,387
    3
    Location:
    TX
    The last few days I've had rounds that did not deprime but will when I put them in for a 2nd pull on the handle. Head stamp F.C. as I recall.

    Loading on a 550. The depriming pin looks fine compared to a spare pin.
     

    Wanna kill these ads? We can help!
  2. Bob2223

    Bob2223
    Expand Collapse
    Jack's buddy!

    Joined:
    Mar 26, 2009
    1,232
    1
    Location:
    Spencer Indiana
    Are ya sure the pin adjusted out far enough?
    The primers may be sticking to the pin and pulling them back in the pocket just enough to keep em from falling.

    Bob
     

  3. CitizenOfDreams

    CitizenOfDreams
    Expand Collapse

    Joined:
    Feb 23, 2009
    8,111
    4
    Location:
    Orlando, FL
    Happened a lot with my RCBS die until I upgraded to their new spring-loaded design. That solved the problem once and for all.
     
  4. Kwesi

    Kwesi
    Expand Collapse

    Joined:
    Sep 23, 2006
    1,387
    3
    Location:
    TX
    I readjusted the die. Turned it down to the shell plate until it was just snug then tightened it ( did not back it off as the manual states ). This is happening to a small % of the rounds.

    Is there another pin adjustment?
     
  5. Bob2223

    Bob2223
    Expand Collapse
    Jack's buddy!

    Joined:
    Mar 26, 2009
    1,232
    1
    Location:
    Spencer Indiana
    I dont know what dies your using but on most sizing dies the pin can be adjusted up and down.



    Bob
     
  6. Kwesi

    Kwesi
    Expand Collapse

    Joined:
    Sep 23, 2006
    1,387
    3
    Location:
    TX
    Standard Carbide dies from Dillon 550.
     
  7. Bob2223

    Bob2223
    Expand Collapse
    Jack's buddy!

    Joined:
    Mar 26, 2009
    1,232
    1
    Location:
    Spencer Indiana
    Dont know nuttin about Dillon stuff. :dunno:





    Bob
     
  8. GLShooter

    GLShooter
    Expand Collapse

    Joined:
    Jan 3, 2006
    403
    0
    Location:
    Phoenix, AZ
    If the decapping rod is screwed in all the way the Dillon should push it off if they are the new type like their instructions say.

    I've never had a primer hang up on any of my Dillon dies. I wouldn't think that a crimped primer would make any difference as long as the pin goes all the way through the flash hole past the base of the case a decent amount.

    I've seen some WCC cases that were crimped in 9MM but have not seen any 9 MM FC's that were.

    Greg
     
  9. Boxerglocker

    Boxerglocker
    Expand Collapse
    Jacks #1 Fan

    Joined:
    Mar 6, 2003
    6,121
    17
    Location:
    Lynnwood, WA
    Common issue for the decaping pin on the newer Dillon dies.... take a piece of 800 grit or finer sandpaper and knock the "squred" (squared) edge of the decapping off, making it slightly rounded. That should fix your issue. I do this with every new pin, even on my SDB.
     
    #9 Boxerglocker, Nov 3, 2010
    Last edited: Nov 3, 2010
  10. GLShooter

    GLShooter
    Expand Collapse

    Joined:
    Jan 3, 2006
    403
    0
    Location:
    Phoenix, AZ
    That was a fix I forgot about from other posters. I had never encountered it myself but it will be there in my mental tool box if it happens in the future.

    Thanks for posting that tip.

    Greg
     
  11. GioaJack

    GioaJack
    Expand Collapse
    Conifer Jack

    Joined:
    Apr 14, 2009
    10,016
    1
    Location:
    Conifer, CO

    Must be one of those Latin words I've been hearing about... huh? :whistling:


    Jack
     
  12. Boxerglocker

    Boxerglocker
    Expand Collapse
    Jacks #1 Fan

    Joined:
    Mar 6, 2003
    6,121
    17
    Location:
    Lynnwood, WA
    Italian actually.... ate some spagetti last night :whistling:
     
  13. GLShooter

    GLShooter
    Expand Collapse

    Joined:
    Jan 3, 2006
    403
    0
    Location:
    Phoenix, AZ
    Pie are round, cake are squred.

    Greg
     
  14. GioaJack

    GioaJack
    Expand Collapse
    Conifer Jack

    Joined:
    Apr 14, 2009
    10,016
    1
    Location:
    Conifer, CO

    Apparently I'm surrounded by public school graduates... or at least part time attendees.

    Teacher: Little Jimmy, what is Keynesian?

    Little Jimmy: Ah, that be where our president really be from.

    Teacher: Correct.



    I fear that we are doomed. :crying:


    Jack
     
  15. ssgrock3

    ssgrock3
    Expand Collapse

    Joined:
    Aug 10, 2003
    1,109
    0
    Location:
    Yukon, Oklahoma
    Sounds like you have crimped military 9mm brass. If it doesn't punch out, it isn't gonna seat for nothing even if she pops out. I usually chuck them in the trash as it slows up my loading and in 9mm that is no fun. are you having any trouble with primer seating on those pieces?
     
    #15 ssgrock3, Nov 3, 2010
    Last edited: Nov 3, 2010
  16. lethal tupperwa

    lethal tupperwa
    Expand Collapse

    Joined:
    Aug 20, 2002
    8,364
    182
    Location:
    Virginia
    pie are round

    corn bread are square!
     
  17. PCJim

    PCJim
    Expand Collapse
    Senior Member

    Joined:
    Aug 4, 2008
    2,950
    0
    Location:
    FL
    Correct Answer! :cool:
     
  18. Kwesi

    Kwesi
    Expand Collapse

    Joined:
    Sep 23, 2006
    1,387
    3
    Location:
    TX
    Keep in mind I only load pistol. I just realized it can't be crimped brass because once it deprimes on the 2nd pull the primer always seats! I called Dillon and they said the primer IS being pushed out but the spent primer is sticking to the pin and being pulled back in. He said it's common with Federal and CCI brass.

    He suggested I take a file to the end of the pin.
     
  19. Boxerglocker

    Boxerglocker
    Expand Collapse
    Jacks #1 Fan

    Joined:
    Mar 6, 2003
    6,121
    17
    Location:
    Lynnwood, WA
    :whistling: Really???
     
  20. GioaJack

    GioaJack
    Expand Collapse
    Conifer Jack

    Joined:
    Apr 14, 2009
    10,016
    1
    Location:
    Conifer, CO

    No one likes a braggart, BG. :outtahere:


    Jack
     
Loading...
Similar Threads Forum Date
Crimped Primers Reloading Mar 5, 2014
Crimped in primers in some 40 cal Winchester rounds? Reloading Aug 22, 2011
Magnum Primers in 9mm Reloading Jan 24, 2011
Crimped Primers, Why? Reloading Dec 30, 2010
Hi primers in factory 9mm Caliber Corner Mar 21, 2010
Duty Gear at CopsPlus