close

Privacy guaranteed - Your email is not shared with anyone.

135gn Nosler

Discussion in '10mm Reloading Forum' started by blastfact, May 5, 2012.


  1. blastfact

    blastfact
    Expand Collapse

    Joined:
    Aug 15, 2011
    1,654
    18
    Location:
    Oklahoma
    I have BD, TG and Herco.

    I've seen data on BD/Blue Dot and it seems very forgiving in use. Not the right powder but it works.

    I've seen data on TG/TightGroup which was surprising. But no reports. And I'm one of those strange folks that like TG in 9mm be it jacketed, plated or lead. I know I'm strange. Does it really have a use in the 10mm 135gn Nolser?

    Poor old Herco gets no respect now days. But I have .38, 9mm and 45 acp loads that shoot great! Has anybody secretly played around with the old school Herco concerning any 135gn 10mm load?

    I also have h-110 and 2400 on hand. A note of importance is all I have right now is mag fed primers. BD seems to love them in heavier bullet weight's of the XTP family.

    So cough it up buddy's. I got the 135's for free so it's time to play with the G20 and LW 5.15" barrel. Within near nuke level's. :)

    Thanks
     

    Wanna kill these ads? We can help!
  2. gofastman

    gofastman
    Expand Collapse

    Joined:
    Jan 29, 2010
    496
    0
    Location:
    MN
    BD is a lot of things, but forgiving is not one of them.
     

  3. blastfact

    blastfact
    Expand Collapse

    Joined:
    Aug 15, 2011
    1,654
    18
    Location:
    Oklahoma
    OK you have been a big NO help. Moving on. (shaking head)
     
  4. _The_Shadow

    _The_Shadow
    Expand Collapse
    Ret. Fireman

    Joined:
    Jul 23, 2007
    4,516
    20
    Location:
    Southeast, LoUiSiAna
    The problem is not with Blue Dot, most JHP's will come apart on impact before you reach the max velocity...in other words "Frag Nasty"!

    With that said 12.0 grains of Blue Dot would be a safe starting point...
     
  5. Yondering

    Yondering
    Expand Collapse

    Joined:
    Dec 3, 2011
    564
    0
    Of the powders you listed, Blue Dot is by far the best for this application; one of the best out there in fact.

    TG and Herco are both too fast, unless you want light loads. H110 and 2400 are way too slow, and won't get up to normal velocity levels before running out of case capacity.
     
  6. Taterhead

    Taterhead
    Expand Collapse
    Counting Beans

    Joined:
    Dec 13, 2008
    3,551
    81
    Location:
    Boise, Idaho
    Load up the Blue Dot... and get ready for a nice fireball!

    Alliant's max for a 155 grain bullet is 12.0 grains, so I agree with the Shadow that it would be a reasonable starting point.
     
  7. blastfact

    blastfact
    Expand Collapse

    Joined:
    Aug 15, 2011
    1,654
    18
    Location:
    Oklahoma
    I went ahead and loaded up 300 rounds with TG and BD.

    The TG load interests me. So I loaded with it from 7.2 to 8.2gn with Fed mag primers.

    As for the BD I loaded from 12 to 13gn with Fed mag primers.

    I pulled my head out of my arse and looked in one of my old log books for loads I had made up back in the days of owning and shooting the worthless Delta Elite. I need to get a chrono in the worse way.
     
  8. XmmAUTO

    XmmAUTO
    Expand Collapse
    10mm Addict

    Joined:
    Dec 31, 2010
    74
    0
    Location:
    Washington
    Blastfact,

    I have gone as high a 14.0 grains in a stock glock barrel with a 20# spring. Average velocity was 1433 FPS. Check out my post on page 3 of the Alliant powder sticky. I have gone as high as 16.0 grains but from 14.5 to 16.0 were fired out of my TC Contender. IIRC 16.0 registered a chrono reading of close to 1700 FPS out of the 4.6: barreled TC. Sorry but no pressure results on that one.
     
  9. TDC20

    TDC20
    Expand Collapse

    Joined:
    Apr 11, 2011
    1,006
    274
    Blastfact,

    I would use caution with Bluedot and magnum primers. I tried substituting CCI#350's for my book max 180gr. load using CCI#300's, without working up (yeah, stupid on my part), and had some significant increases in pressure indications. Also got about 85fps more velocity. Maybe at lower pressures Bluedot and magnum primers are less of an issue. Don't misunderstand me, I'm not saying not to use magnum primers and Bluedot, just be aware that you will reach max pressure much sooner than with standard primers. Substitutions with warm to hot loads are a no-no in my experience. I'm with gofastman on this one.

    You would be better served to pick up some Longshot for loading hot 135's. It's easy to work with and you should be able to get close to 1600fps with that barrel and standard primers. You can probably get there with 800X, too, but use standard primers and go slow. I think trying to get anywhere near that velocity with Bluedot and magnum primers would be a BIG mistake.

    Longshot is a great all-around 10mm powder. If you don't own any, you should try it. Also, I would advise getting some standard primers for 10mm. Standard primers have worked better for me in every load that I've done a standard-magnum primer comparison.

    Good luck and be safe!
     
    #9 TDC20, May 6, 2012
    Last edited: May 6, 2012
  10. blastfact

    blastfact
    Expand Collapse

    Joined:
    Aug 15, 2011
    1,654
    18
    Location:
    Oklahoma
    I'm off to do some shooting.

    Taking the G20, 686P, M&P .45, 9mm and the PF-9.

    The G20 will get to eat all sorts of ammo. :)
     
Loading...
Similar Threads Forum Date
Nosler no. 7 Manual 10mm Reloading Forum Feb 19, 2015
Nosler JHP Reloading Jul 26, 2012
Nosler bullets 10mm Reloading Forum Dec 12, 2010
Nosler 9mm JHP Reloading Aug 5, 2010
Nosler Explosion Reloading Jun 2, 2010