so I got some parts for my glock 23 gen 2. I put in a apex trigger with the 3rd gen trigger connector bar, installed a zev 3.5 lb connector and spring kit for the connector / plunger / striker spring. I also swapped to an apex low weight plunger and a glock extended slide stop and installed an extended slide lock release. I really like the trigger pull, not super light but very crisp and controllable.
I would recommend the apex glock trigger to anyone looking for a metal wider flatter trigger. I bought mine with the gen 3 glock trigger connector attached so I can easily swap it back if I want.
I bought a new glock 32 barrel so that I can carry 357 sig which I like a lot. I am running a new glock standard recoil spring , but I likely will go to a metal guide rod.
I have Apex triggers in most of my Glock's. The bad thing about doing one is it ruins your perception of the standard trigger. I recently installed a Zev in one of my 23s and I'm afraid there might be more on the horizon.
I've got one I'm my 23, but no internal changes. It's a comfortable trigger. I only wish Glock would fix their triggers so the trigger safety fully recess when pulled.
I agree with Bucky, what I thought was the grooved trigger causing pain in my trigger finger, I now think it is the safety sticking out more than the trigger face.
I have long fingers, and learned to shoot a 1911 with just the tip of my finger, because I would be pushing shots to the left.
I have learned to shoot Glocks the same way, and the safety hurts after a while. I changed out a couple of triggers to a smooth face, and it didn't help much.
I don't want to get started buying new triggers for all my Glocks. Guess I need to start sanding and polishing trigger safeties.
I shoot with the tip of my trigger finger as well. I thought it was the grooved trigger as well, but replaced it with a factory smooth trigger, and still got the discomfort after prolonged shooting. Perhaps this method of shooting is why the non-recessed trigger blade is effecting us more than others.
I tried sanding the trigger on my 19 and that seemed to work well, but still not as comfortable as the Apex. Still, the Apex isn't cheap, and it does scream "modified gun". (BTW: Let's not dirty this thread by debating the implications of that here. There is an ongoing thread to discuss your opinions on this. http://www.glocktalk.com/threads/ar...-shoot-someone-with-a-customized-gun.1650771/
)
For most shooters with hands large enough to hold a Glock properly, it probably makes sense to vary position of the trigger finger. It's probably easiest to press the trigger straight back somewhere near the middle of the pad. And it's probably easiest to shoot fast splits up near the tip.
The unmodified trigger safety causes a number of problems. It's uncomfortable, gives negative feedback, is difficult to change indexes on, etc. You have to be careful about changing it if you're working with rules that restrict external modifications. But even in that case, you can make vast improvements in just a few minutes.
And I concur about the apex. I run them on all my carry weapons. x2 19s, and a 17. I run a zev on my competition gun. If you're looking for a more comfortable, and slightly smoother trigger that still uses OEM parts to maintain reliability, you can't beat the Apex.
Careful with the striker spring. I did the Zev and had a couple of FTF. Went back stock on that part. I have overwatch tac trigger, Zev race connector and Zev trigger spring and mine is crisp.
They make more than one weight. I find that with the #2 spring, you can get light primer strikes, even with a lightened firing pin. (this has been my experience). I now run the #3 spring, and have zero issues. (race gun, not carry gun)
I agree with Bucky, what I thought was the grooved trigger causing pain in my trigger finger, I now think it is the safety sticking out more than the trigger face.
I have long fingers, and learned to shoot a 1911 with just the tip of my finger, because I would be pushing shots to the left.
I have learned to shoot Glocks the same way, and the safety hurts after a while. I changed out a couple of triggers to a smooth face, and it didn't help much.
I don't want to get started buying new triggers for all my Glocks. Guess I need to start sanding and polishing trigger safeties.
so I got some parts for my glock 23 gen 2. I put in a apex trigger with the 3rd gen trigger connector bar, installed a zev 3.5 lb connector and spring kit for the connector / plunger / striker spring. I also swapped to an apex low weight plunger and a glock extended slide stop and installed an extended slide lock release. I really like the trigger pull, not super light but very crisp and controllable.
I would recommend the apex glock trigger to anyone looking for a metal wider flatter trigger. I bought mine with the gen 3 glock trigger connector attached so I can easily swap it back if I want.
I'm really pleased to hear all of this. I had looked at the Pyramid Triggers at GlockStore, but was unimpressed with them. Especially for the money. I also could not get consistent information about the trigger bar. Is it OEM, or a propriatery one they manufacture?
Anyway, stopping to pick up an Apex this morning...
Now I'm a bit concerned, I'm using one of the Polymer80 frames and I think the trigger well is slightly smaller. I wonder now if this trigger may be slightly too long due to it being flat. I'm sitting here in front of the gun store now waiting for them to open. Hopefully it will fit.
There is no rubbing issue. And no mods to the stock glock to install the trigger. I changed out some other stuff but the trigger made the gun feel like a much more expensive gun in 15 minutes.
so I got some parts for my glock 23 gen 2. I put in a apex trigger with the 3rd gen trigger connector bar, installed a zev 3.5 lb connector and spring kit for the connector / plunger / striker spring. I also swapped to an apex low weight plunger and a glock extended slide stop and installed an extended slide lock release. I really like the trigger pull, not super light but very crisp and controllable.
I would recommend the apex glock trigger to anyone looking for a metal wider flatter trigger. I bought mine with the gen 3 glock trigger connector attached so I can easily swap it back if I want.
Dropped in the Apex tactical trigger in both my 23 and 27. Love 'em, it has changed the entire feel of the trigger. I've always loved the flat trigger on 1911's, the Apex trigger gives a somewhat similar feel to my glocks. This, of course, is simply due to the changing of the geometry of the trigger itself. The trigger pull hasn't been lightened, it is just a smoother, better feel.
I'm COMPLETELY satisfied with mine. At first I was afraid of justifying the cost but it was definitely a worthy upgrade.
Now I need to upgrade my sights for my Birthday at the end of May.
How thick is the width of the triggers safety lever?
The Zev safety is way too wide and my finger sinks into it and it distracts me. It would also be nice if the safety bottomed out flat, and wouldn't sink farther in than the triggers face.
It looks thin enough:
If the safety lever is no thicker than the stock plastic one, guess who's idea that was?
Thanks. That answers my question. Guess I'll have to try one. Wonder if they'll give me a discount? Then again, maybe they'll charge me extra cause my idea made them retool.
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Related Threads
?
?
?
?
?
Glock Talk
21M posts
185.2K members
Since 1999
A forum community dedicated to Glock firearm owners and enthusiasts. Come join the discussion about optics, gunsmithing, styles, reviews, troubleshooting, accessories, classifieds, and more!