Home Forums Classifieds Blogs Today's Posts Search Social Groups



  
SIGN-UP
Notices

Glock Talk
Welcome To The Glock Talk Forums.

 
  
Reply
 
Thread Tools Display Modes
Old 10-07-2012, 07:15   #1
ADK_40GLKr
Senior Member
 
ADK_40GLKr's Avatar
 
Join Date: Nov 2010
Location: RFD NY Adks
Posts: 2,210
Blog Entries: 2
Fat cases?

Just sat down for the first time, with my Lee single stage press and 100 once used .40 brass, deprimed and then reprimed them. I made sure I used the resizing die when I installed the new primers.

It was then I noticed that some were rather fat in the middle, not at the base where Glock's infamous lack of support is supposed to be.

Assuming they'll drop into my barrel OK when I check for fit, should I worry about loading and firing these?
__________________
There's a fundamental flaw in a system that passes laws that put an onerous burden on law-abiding citizens, but fails to prosecute the criminals who break those laws.
ADK_40GLKr is offline   Reply With Quote
Old 10-07-2012, 07:30   #2
steve4102
Senior Member
 
steve4102's Avatar
 
Join Date: Jan 2009
Posts: 1,058
pictures?
__________________
Give a man a fish and he eats for a day. Give a man a welfare check, a forty ounce malt liquor, a crack pipe and some Air Jordan's and he votes Democrat for a lifetime.
steve4102 is offline   Reply With Quote
Old 10-07-2012, 15:41   #3
ADK_40GLKr
Senior Member
 
ADK_40GLKr's Avatar
 
Join Date: Nov 2010
Location: RFD NY Adks
Posts: 2,210
Blog Entries: 2
Did I mention I'm a total newbie to reloading?

Quote:
Originally Posted by steve4102 View Post
pictures?
Don't care whether I'm seen with them as long as what is heard is not KA-BOOM!

I measured one with my CHEAP caliper and both top and middle read .42 though it moved some within that range. Here's a photo, the bulge is most noticeable with the one on the left.

Edit: When I went back to take photos, I tried loading and seating the bullet in a couple, and what I found was the bullet pushed all the way into the case. So I'm guessing that the seating die was loose, and probably the sizing die was also, thus not re-shaping the shell.

As I'm not clear on the terminology for the parts of the dies, its going to be difficult to understand any responses to the question on how to set up the dies.

I think I'll take em back to my LGS, and ask the tech how to do it properly.

(I'm beginning to understand why some noobs ask such stupid questions about Glocks!)
__________________
There's a fundamental flaw in a system that passes laws that put an onerous burden on law-abiding citizens, but fails to prosecute the criminals who break those laws.

Last edited by ADK_40GLKr; 12-13-2012 at 12:26..
ADK_40GLKr is offline   Reply With Quote
Old 10-07-2012, 08:13   #4
Colorado4Wheel
Senior Member
 
Colorado4Wheel's Avatar
 
Join Date: Nov 2006
Location: CO
Posts: 14,354
How about just measuring it and giving some concrete information.
__________________
Steve
Colorado4Wheel is offline   Reply With Quote
Old 10-07-2012, 12:50   #5
WiskyT
Malcontent
 
WiskyT's Avatar
 
Join Date: Jun 2002
Location: North Carolina
Posts: 11,764
Quote:
Originally Posted by Colorado4Wheel View Post
How about just measuring it and giving some concrete information.
You don't need to quantify "fat". If you don't want to be seen with it, it's fat. If you're kind of proud of it, it's "thick".
__________________
Drugs are bad because if you do drugs you're a hippie and hippies suck.
Eric Cartman


"If you kill enough of them, they stop fighting."-General Curtis E. LeMay
WiskyT is offline   Reply With Quote
Old 10-07-2012, 13:02   #6
sig357fan
Senior Member
 
Join Date: Apr 2008
Posts: 727
ADK_40GLKr,

couple of questions.....

cases all the same head stamp or mixed brass?
were the cases cleaned proir to sizing, how?
all fired in the same weapon?
any discoloration, cracks/scratches in the area of the bulge before or after sizing?
how did you determine that the cases were bulged in the middle?

thats all I can think of.

sig357fan
sig357fan is offline   Reply With Quote
Old 10-07-2012, 15:17   #7
Colorado4Wheel
Senior Member
 
Colorado4Wheel's Avatar
 
Join Date: Nov 2006
Location: CO
Posts: 14,354
Quote:
Originally Posted by WiskyT View Post
You don't need to quantify "fat". If you don't want to be seen with it, it's fat. If you're kind of proud of it, it's "thick".
I love a good coke bottle shape.
__________________
Steve
Colorado4Wheel is offline   Reply With Quote
Old 10-07-2012, 16:09   #8
ADK_40GLKr
Senior Member
 
ADK_40GLKr's Avatar
 
Join Date: Nov 2010
Location: RFD NY Adks
Posts: 2,210
Blog Entries: 2
Quote:
Originally Posted by WiskyT View Post
You don't need to quantify "fat". If you don't want to be seen with it, it's fat. If you're kind of proud of it, it's "thick".
How about "Pleasantly Plump"?
__________________
There's a fundamental flaw in a system that passes laws that put an onerous burden on law-abiding citizens, but fails to prosecute the criminals who break those laws.
ADK_40GLKr is offline   Reply With Quote
Old 10-07-2012, 16:22   #9
Colorado4Wheel
Senior Member
 
Colorado4Wheel's Avatar
 
Join Date: Nov 2006
Location: CO
Posts: 14,354
Are you even sizing. No way the sized case would allow a bullet to seat that easily.
__________________
Steve
Colorado4Wheel is offline   Reply With Quote
Old 10-07-2012, 16:36   #10
F106 Fan
Senior Member
 
F106 Fan's Avatar
 
Join Date: Oct 2011
Posts: 5,969
In broad terms, you adjust the sizing die down until it impacts the shell holder when the ram is fully up. I set it down a little further (1/8 turn?) such that the press cams over in an effort to get all the slack out. Some dies have the carbide exposed right at the end of the die. Others have it recessed a couple of thousandths. If the carbide is exposed, it might not be a good idea to have the press cam over. It could crack the carbide. In any event, the die needs to be fully touching the shell holder when there is a case being sized.

Ordinarily, sizing dies are pretty precise and they need to go all the way down the case.

It has nothing to do with your situation but I'll throw it out anyway: I really like using Hornady One Shot case lube on my cases even though I am using a carbide die. It makes the process a lot smoother and easier on the arm.

Richard
__________________
"No matter how cynical you become, it's never enough to keep up." - Lily Tomlin
F106 Fan is offline   Reply With Quote
Old 10-07-2012, 18:39   #11
unclebob
Senior Member
 
unclebob's Avatar
 
Join Date: Oct 2000
Location: Mary Esther FL
Posts: 6,886
I would say that either the wrong sizing die was used. The carbide ring is missing. Or the sizing die was not set up properly. Maybe steel cases? Cases fired in a Glock has nothing to do with it. Me and 3 other people that I shoot with. We all use mixed range pickup brass, and we all shoot Glocks. With well over a million rounds fired of range pickup brass. You might have problems with range pickup brass that have been shot in some full auto machine firearms. But just because it was fired in a Glock has nothing to do with anything. Unless you are pushing the upper limits of max loads. And that could be with any pistol.
__________________
Team Carver Custom
NRA Certified Instructor
NRA Benefactor Life Member
GSSF Life Member
___________________________________________
unclebob is offline   Reply With Quote
Old 10-07-2012, 19:00   #12
SARDG
Senior Member
 
SARDG's Avatar
 
Join Date: Nov 2006
Location: Florida's Left Coast
Posts: 7,656
Quote:
Originally Posted by unclebob View Post
I would say that either the wrong sizing die was used........
The picture's well out of focus, but it does look more like a .45 sizer was used, than a .40.
SARDG is offline   Reply With Quote
Old 10-07-2012, 21:19   #13
ADK_40GLKr
Senior Member
 
ADK_40GLKr's Avatar
 
Join Date: Nov 2010
Location: RFD NY Adks
Posts: 2,210
Blog Entries: 2
Quote:
Originally Posted by SARDG View Post
The picture's well out of focus, but it does look more like a .45 sizer was used, than a .40.
OK, Here's what went wrong: the decapper came loose and I set it too low. So when I was "decapping", I wasn't running the sizer all the way down the case. Went back to the bench and resized a few with the decapper out, and THAT worked fine.

Also set the seater for the right length - approx 1.12
(And what good is a caliper that only measures to .01"?) and was able to pull and re-seat a couple bullets...

So now I have 95 PRIMED .40 cases that need to be resized properly, and I don't think I'd better fill any more cases until I have a good scale and a decent caliper.

The 5 I made the other day measured 1.12' on that CHEAP digital caliper and fired OK at the range. I had 5 others that I had crimped too short, and couldn't pull the bullets, so I'll just chalk them up to the cost of learning.

Like I said, I'm a real novice at re-loading, but I want to learn to do this right.
__________________
There's a fundamental flaw in a system that passes laws that put an onerous burden on law-abiding citizens, but fails to prosecute the criminals who break those laws.
ADK_40GLKr is offline   Reply With Quote
Old 10-07-2012, 21:57   #14
SARDG
Senior Member
 
SARDG's Avatar
 
Join Date: Nov 2006
Location: Florida's Left Coast
Posts: 7,656
I cannot even imagine what kind of cheap caliper you may have that has only a resolution of .01". The $20 Harbor Frieght models go to .0005 (inch) resolution, but read in .01 mm resolution. It sounds as though you are reading inches, but...

There are plenty of odds and ends you really should have in this 'hobby'; the aforementioned check-weights and a bullet puller are but 2 of them. You can actually get collet style pullers that will work in your press.

Since you are using a SS press, you should have plenty of time and opportunity to examine your work prior to making 100 similar mistakes.
SARDG is offline   Reply With Quote
Old 10-08-2012, 07:01   #15
ADK_40GLKr
Senior Member
 
ADK_40GLKr's Avatar
 
Join Date: Nov 2010
Location: RFD NY Adks
Posts: 2,210
Blog Entries: 2
Quote:
Originally Posted by SARDG View Post
I cannot even imagine what kind of cheap caliper you may have that has only a resolution of .01". The $20 Harbor Frieght models go to .0005 (inch) resolution, but read in .01 mm resolution. It sounds as though you are reading inches, but...

There are plenty of odds and ends you really should have in this 'hobby'; the aforementioned check-weights and a bullet puller are but 2 of them. You can actually get collet style pullers that will work in your press.

Since you are using a SS press, you should have plenty of time and opportunity to examine your work prior to making 100 similar mistakes.
Yep, LGS gave me a good product in the Lee Press, but sold me the cheapest, most useless caliper he had!

He had a nice digital scale I decided not to get at the time. That collet bullet puller sounds like it would be very useful. Probably NOT a very costly mistake, but I HATE wasting materials. Don't mind burning tens of $ in a shooting session, but it goes against my grain to DISCARD a single cartridge I've assembled!

Gonna see if Lowes might have the kind of scales and calipers I need.

Maybe if I get just a little more info (& less ignorant) I'd be wise to start buying on-line!
__________________
There's a fundamental flaw in a system that passes laws that put an onerous burden on law-abiding citizens, but fails to prosecute the criminals who break those laws.
ADK_40GLKr is offline   Reply With Quote
Old 10-08-2012, 07:21   #16
ADK_40GLKr
Senior Member
 
ADK_40GLKr's Avatar
 
Join Date: Nov 2010
Location: RFD NY Adks
Posts: 2,210
Blog Entries: 2
Lee Loading Chart

I notice that for a few powders and bullets, the chart has an entry in the "Lee Dipper" column.

I'm using 165 gr plated bullets. But the chart says .5 cc under the 170 gr XTP & doesn't mention 165at all. I know it's OK to use the load for the lighter bullet, but is there a significant difference between XTP & plated?

And... Why do the few plated bullets in the chart have their own type of powder?
__________________
There's a fundamental flaw in a system that passes laws that put an onerous burden on law-abiding citizens, but fails to prosecute the criminals who break those laws.

Last edited by ADK_40GLKr; 10-08-2012 at 07:29.. Reason: Add Q.
ADK_40GLKr is offline   Reply With Quote
Old 10-08-2012, 07:38   #17
SARDG
Senior Member
 
SARDG's Avatar
 
Join Date: Nov 2006
Location: Florida's Left Coast
Posts: 7,656
Quote:
Originally Posted by ADK_40GLKr View Post
Yep, LGS gave me a good product in the Lee Press, but sold me the cheapest, most useless caliper he had!

Gonna see if Lowes might have the kind of scales and calipers I need.

Maybe if I get just a little more info (& less ignorant) I'd be wise to start buying on-line!
PLEASE use the search function on this forum and read and heed other's advice. This sub-forum is literally bursting at the seams with folks who ask for advice, receive the advice of experienced reloaders, then go off and do just the opposite from what is recommended to them - many only to realize that they should have taken the advice in the first place.

If you want an attractive bathroom scale - go to Lowes. Otherwise..... search for 'scale' on this forum. It doesn't have to be digital - clearly a beam scale has your current system beat for speed and acuracy.

If you want cheap functional digital calipers, go to Harbor Frieght - though it even seems like the later HF $20 dig calipers aren't so functional any longer.
http://glocktalk.com/forums/showthread.php?t=1445504
SARDG is offline   Reply With Quote
Old 10-08-2012, 08:19   #18
ADK_40GLKr
Senior Member
 
ADK_40GLKr's Avatar
 
Join Date: Nov 2010
Location: RFD NY Adks
Posts: 2,210
Blog Entries: 2
Thanks

Quote:
Originally Posted by SARDG View Post
If you want an attractive bathroom scale - go to Lowes.


Thanks, my friends!

...and I didn't get to be 69.75 YO by being careless! I am seriously rethinking my "Inexpensive reloading" venture. It seems a little more equipment will be a wise investment.

I appreciate all the input.

(btw Sardge: your PM inbox is full)
__________________
There's a fundamental flaw in a system that passes laws that put an onerous burden on law-abiding citizens, but fails to prosecute the criminals who break those laws.

Last edited by ADK_40GLKr; 10-08-2012 at 08:23..
ADK_40GLKr is offline   Reply With Quote
Old 10-08-2012, 08:50   #19
SARDG
Senior Member
 
SARDG's Avatar
 
Join Date: Nov 2006
Location: Florida's Left Coast
Posts: 7,656
Quote:
Originally Posted by ADK_40GLKr View Post
...I appreciate all the input.

(btw Sardge: your PM inbox is full)
I know... because I rather dislike PMs. HOWEVER, you may click on my screen name on the left and send me an e-mail. I love e-mails...
SARDG is offline   Reply With Quote
Old 10-08-2012, 08:54   #20
ColoCG
Senior Member
 
ColoCG's Avatar
 
Join Date: Mar 2011
Location: Colorado
Posts: 928
It also sounds as if you should invest in at least 1, 2 or more are better good reloading manuals such as Lyman, Speer, or Hornady are a few. These manuals will aswer most of your questions about die set up, and reloading equipment in general, as well as providing starting loads listed in grains of weight for most cartridges.
__________________
Charlie
ColoCG is offline   Reply With Quote

 
  
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump




All times are GMT -6. The time now is 22:53.




Homepage
FAQ
Forums
Calendar
Advertise
Gallery
GT Wiki
GT Blogs
Social Groups
Classifieds


Users Currently Online: 925
229 Members
696 Guests

Most users ever online: 2,672
Aug 11, 2014 at 2:31